B1C2E13 - TroubleshootingB1C2E13-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
B1C2E13	Internal and external air servo motor drive line open circuit内外气伺服电机驱动线开路	1. The fresh/recirculation air servo motor drive circuit is open circuit1.内外气伺服电机驱动电路开路

Troubleshooting steps故障诊断步骤

①General inspection (taking the left cycle executor as an example for inspection)一般检查(以左循环执行器为例进行检查)
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Check the left circulation actuator wiring harness for damage, breakage, etc.检查左循环执行器线束是否存在损坏、断裂等现象。 3. Check the left circulation actuator wiring harness connector for loose connection or damage.检查左循环执行器线束接插件是否存在虚接、损坏等现象。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 2.去步骤2。 No否 Repair or replace faulty wiring harness or connector.维修或更换故障线束或接插件。
②Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 3.去步骤3。
③Check the left cycle actuator motor drive circuit检查左循环执行器电机驱动线路
	1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Disconnect the thermal management integrated module harness connector FB44 and the left circulation actuator harness connector AC05.断开热管理集成模块线束接插件FB44和左循环执行器线束接插件AC05。 3. Use a digital multimeter to measure the resistance between pin 20/8 of FB44 and pin 4/5 of AC05.用数字万用表测量FB44的20/8号针脚与AC05的4/5号针脚之间的电阻。 Standard resistance value: <1标准电阻值：＜1 Ω Are the test results normal?检查结果是否正常？ Yes是 Go to step 4.去步骤4。 No否 Repair or replace the left cycle actuator motor drive harness.维修或更换左循环执行器电机驱动线束。
④Replace left cycle actuator更换左循环执行器
1. Replace the left circulation actuator with a new one and check whether the fault code and symptoms are eliminated.更换新的左循环执行器，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 5.去步骤5。
⑤Replacing the thermal management integrated module更换热管理集成模块
1. Replace the thermal management integrated module with a new one and check whether the fault code and symptoms are eliminated.更换新的热管理集成模块，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。   Caution:注意： ♦  After replacing the thermal management integrated module, you need to use a diagnostic instrument to recalibrate the thermal management integrated module.更换热管理集成模块后，需用诊断仪对热管理集成模块重新标定。