B1C0A01 - TroubleshootingB1C0A01-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
B1C0A01	Passenger air-mix (blend door) motor drive line short circuit副驾混风电机驱动线短路	1. The driving circuit of the air-mix (blend door) servo motor on the passenger side is short-circuited.1.副驾侧混风伺服电机驱动电路短路

Troubleshooting steps故障诊断步骤

①General inspection一般检查
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Check the right hybrid actuator wiring harness for damage, breakage, etc.检查右混合执行器线束是否存在损坏、断裂等现象。 3. Check the right hybrid actuator harness connector for loose connection or damage.检查右混合执行器线束接插件是否存在虚接、损坏等现象。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 2.去步骤2。 No否 Repair or replace faulty wiring harness or connector.维修或更换故障线束或接插件。
②Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 3.去步骤3。
③Check the right hybrid actuator motor drive circuit检查右混合执行器电机驱动线路
	1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Disconnect the thermal management integrated module harness connector FB44 and the right hybrid actuator harness connector AC13.断开热管理集成模块线束接插件FB44和右混合执行器线束接插件AC13。 3. Use a digital multimeter to measure the resistance between pin 9/21 of FB44 and ground.用数字万用表测量FB44的9/21号针脚与接地之间的电阻。 Standard resistance value: >1M标准电阻值：＞1M Ω Are the test results normal?检查结果是否正常？ Yes是 Go to step 4.去步骤4。 No否 Repair or replace the right hybrid actuator motor drive circuit.维修或更换右混合执行器电机驱动线路。
④Replace right mix actuator更换右混合执行器
1. Replace the right mix actuator with a new one and check whether the fault code and symptoms are eliminated.更换新的右混合执行器，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 5.去步骤5。
⑤Replacing the thermal management integrated module更换热管理集成模块
1. Replace the thermal management integrated module with a new one and check whether the fault code and symptoms are eliminated.更换新的热管理集成模块，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。   Caution:注意： ♦  After replacing the thermal management integrated module, you need to use a diagnostic instrument to recalibrate the thermal management integrated module.更换热管理集成模块后，需用诊断仪对热管理集成模块重新标定。