Troubleshooting › Seat › Diagnosis
B2B0017-故障诊断 · T00607853

 B2B0017 - TroubleshootingB2B0017-故障诊断

Fault code description故障码说明
DTC故障码(DTC)
Fault code description故障码描述
Possible cause of failure可能故障原因
B2B0017
The input voltage is higher than the upper limit value输入电压高于上限值
1. Abnormal power supply wiring harness1.供电线束异常
2. The power supply module is abnormal2.供电模块异常
Troubleshooting steps故障诊断步骤
①Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 2.去步骤2。
②Check 12V battery voltage检查蓄电池电压
1. Power status is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”,断开蓄电池负极。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。
Standard voltage value: about 12.5V标准电压值：约12.5V
Are the test results normal?检查结果是否正常？
Yes是 Go to step 4.去步骤4。
No否 Go to step 3.去步骤3。
③Check DCDC output voltage检查DCDC输出电压
1. The vehicle is powered on.车辆上电。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。
Standard voltage value: about 14V标准电压值：约14V
Are the test results normal?检查结果是否正常？
Yes是 Discharge the 12V battery.对蓄电池进行放电。
No否 Inspect DCDC and its lines.检修DCDC及其线路。
④Replace seat controller更换座椅控制器
1. Replace the seat controller with a new one and check whether the fault code and symptoms are eliminated.更换新的座椅控制器，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Look for causes from other symptoms.从其他症状查找原因。
  Caution:注意：
♦  Any repairs on the passenger seat with a seat controller (replacement of the entire seat and software flash of the seat controller are included), after the repair, it is necessary to use a diagnostic tool to clear the position information of the seat controller (when the diagnostic tool is operated, the vehicle remains in the Ready state), and inform the user that the position information has been cleared and the seat position needs to be re-memorized. Otherwise, the position information will be incorrect due to maintenance, resulting in the failure of related functions of the passenger seat.所有带座椅控制器的副驾驶座椅的任何维修（座椅整椅的更换、座椅控制器的软件刷新都包含在内），在维修后，都需要使用诊断仪对座椅控制器进行位置信息清除操作（诊断仪操作时，整车保持为Ready状态），并告知用户位置信息已清除，需要重新记忆座椅位置，否则会因为维修导致位置信息错误，导致副驾驶座椅相关功能失效。