U207387 - TroubleshootingU207387-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
U207387	PADS message lost (LIN node)PADS报文丢失（LIN节点）	1.PADS node is offline1.PADS节点离线
		2.PADS node is damaged2.PADS节点损坏
		3. The PADS node does not send messages according to the scheduled period.3.PADS节点未按预定周期发出报文

Troubleshooting steps故障诊断步骤

①Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 2.去步骤2。
②General inspection一般检查
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Check whether the combined switch and clock spring assembly wiring harness is damaged or broken.检查组合开关与时钟弹簧总成线束是否存在损坏、断裂等现象。 3. Check whether the combination switch and clock spring assembly wiring harness connectors are connected or damaged.检查组合开关与时钟弹簧总成线束接插件是否存在虚接、损坏等现象。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 3.去步骤3。 No否 Repair or replace faulty wiring harness or connector.维修或更换故障线束或接插件。
③Check the communication harness between the gateway controller and combination switch and clock spring assembly检查网关控制器和组合开关与时钟弹簧总成之间的通讯线束
	1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Disconnect the gateway controller harness connector IP62 and the combined switch and clock spring assembly harness connector IP31/IP33.断开网关控制器线束接插件IP62和组合开关和时钟弹簧总成线束接插件IP31/IP33。 3. Use a digital multimeter to measure the resistance between pin 6 of IP62 and pin 5 of IP31.使用数字万用表测量IP62的6号针脚与IP31的5号针脚之间的电阻。 Standard resistance value: <1标准电阻值：＜1 Ω
	d. Use a digital multimeter to measure the resistance between pin 6 of IP62 and pin 3 of IP33.d.使用数字万用表测量IP62的6号针脚与IP33的3号针脚之间的电阻。 Standard resistance value: <1标准电阻值：＜1 Ω Are the test results normal?检查结果是否正常？ Yes是 Go to step 4.去步骤4。 No否 Repair or replace the faulty wiring harness.维修或更换故障线束。
④Replace the combination switch and clock spring assembly更换组合开关与时钟弹簧总成
1. Replace the combined switch and clock spring assembly with a new one, and check whether the fault code and symptoms are eliminated.更换新的组合开关与时钟弹簧总成，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 5.去步骤5。   Caution:注意： ♦  After replacing the combination switch and clock spring assembly, you need to use a diagnostic instrument to recalibrate the combination switch and clock spring assembly.更换组合开关与时钟弹簧总成后，需用诊断仪对组合开关与时钟弹簧总成重新标定。
⑤Replace steering wheel switch assembly更换方向盘开关总成
1. Replace the steering wheel switch assembly with a new one and check whether the fault code and symptoms are eliminated.更换新的方向盘开关总成，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 6.去步骤6。
⑥Replace gateway controller更换网关控制器
1. Replace with a new gateway controller and check whether the fault code and symptoms are eliminated.更换新的网关控制器，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。   Caution:注意： ♦  After replacing the gateway controller, you need to use a diagnostic tool to recalibrate the gateway controller.更换网关控制器后，需用诊断仪对网关控制器重新标定。