U015587 - TroubleshootingU015587-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
U015587	Lost communication with ICM与ICM丢失通讯	1. The communication harness is disconnected or the module is lost1.通讯线束断开或模块丢失

Troubleshooting steps故障诊断步骤

①Power-on inspection (taking the left front door control module fault report as an example)上电检查(以报左前门控制模块故障为例)
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 2.去步骤2。
②General inspection一般检查
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Check whether the BCAN communication harness is damaged or broken.检查BCAN通讯线束是否存在损坏、断裂等现象。 3. Check the BCAN communication harness connector for loose connections or damage.检查BCAN通讯线束接插件是否存在虚接、损坏等现象。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 3.去步骤3。 No否 Repair or replace the BCAN communication harness or connector.维修或更换BCAN通讯线束或接插件。
③Check the communication harness between the left front door control module and the infotainment head unit检查左前门控制模块与车载智能多媒体主机之间的通讯线束
	1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Disconnect the left front door control module 2 harness connector FL17 and the vehicle infotainment head unit 2 harness connector IP48.断开左前门控制模块2线束接插件FL17和车载智能多媒体主机2线束接插件IP48。 3. Use a multimeter to measure the resistance between pins 9/10 of FL17 and pins 21/22 of IP48.使用万用表测量FL17的9/10号针脚和IP48的21/22号针脚之间的电阻。 Standard resistance value: <1标准电阻值：＜1Ω Are the test results normal?检查结果是否正常？ Yes是 Go to step 4.去步骤4。 No否 Repair or replace the faulty wiring harness.维修或更换故障线束。
④Check the infotainment head unit system检查车载智能多媒体主机系统
1. Power status "OFF".电源状态“OFF”。 2. Connect the diagnostic tool.连接诊断仪。 3. Power status "ON".电源状态“ON”。 4. Use the diagnostic tool to check the vehicle's infotainment head unit system.使用诊断仪检查车载智能多媒体主机系统。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 5.去步骤5。 No否 Overhaul the infotainment head unit system.检修车载智能多媒体主机系统。
⑤Replace left front door control module更换左前门控制模块
1. Replace the left front door control module with a new one and check whether the fault code and symptoms are eliminated.更换新的左前门控制模块，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。   Caution:注意： ♦  After replacing the left front door control module, you need to use a diagnostic tool to recalibrate the left front door control module.更换左前门控制模块后，需用诊断仪对左前门控制模块重新标定。