Troubleshooting › Air bag system › Diagnosis
B009513-故障诊断 · T00607222

 B009513 - TroubleshootingB009513-故障诊断

Fault code description故障码说明
DTC故障码(DTC)
Fault code description故障码描述
Possible cause of failure可能故障原因
B009513
Passenger front impact acceleration sensor open circuit乘员前碰加速度传感器开路
1. The passenger front collision acceleration sensor is open circuit1.乘员前碰加速度传感器开路
Troubleshooting steps故障诊断步骤
①General inspection一般检查
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。
2. Check the right front collision sensor wiring harness for damage, breakage, etc.检查右前碰撞传感器线束是否存在损坏、断裂等现象。
3. Check the right front collision sensor harness connector for loose connection or damage.检查右前碰撞传感器线束接插件是否存在虚接、损坏等现象。
Are the test results normal?检查结果是否正常？
Yes是 Go to step 2.去步骤2。
No否 Repair or replace faulty wiring harness or connector.维修或更换故障线束或接插件。
②Check the wiring harness from the airbag electronic control unit to the right front impact sensor检查安全气囊电控单元至右前碰撞传感器之间的线束
Graphic
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。
2. Disconnect the airbag electronic control unit harness connector BD51 and the right front collision sensor harness connector FB34.断开安全气囊电控单元线束接插件BD51和右前碰撞传感器线束接插件FB34。
3. Use a digital multimeter to measure the resistance between pin 9/10 of BD51 and pin 2/1 of FB34.用数字万用表测量BD51的9/10号针脚与FB34的2/1号针脚之间的电阻。
Standard resistance value: <1标准电阻值：＜1 Ω
Are the test results normal?检查结果是否正常？
Yes是 Go to step 3.去步骤3。
No否 Repair or replace the wiring harness from the airbag electronic control unit to the right front impact sensor.维修或更换安全气囊电控单元至右前碰撞传感器之间的线束。
③Replace right front collision sensor更换右前碰撞传感器
1. Replace the right front collision sensor with a new one and check whether the fault code and symptoms are eliminated.更换新的右前碰撞传感器，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 4.去步骤4。
④Replace airbag electronic control unit更换安全气囊电控单元
1. Replace the airbag electronic control unit with a new one and check whether the fault code and symptoms are eliminated.更换新的安全气囊电控单元，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Look for causes from other symptoms.从其他症状查找原因。
  Caution:注意：
♦  After replacing the airbag electronic control unit, you need to use a diagnostic tool to recalibrate the airbag electronic control unit.更换安全气囊电控单元后，需用诊断仪对安全气囊电控单元重新标定。