Troubleshooting › Air bag system › Diagnosis
B100016-故障诊断 · T00607178

 B100016 - TroubleshootingB100016-故障诊断

Fault code description故障码说明
DTC故障码(DTC)
Fault code description故障码描述
Possible cause of failure可能故障原因
B100016
low voltage error电压过低错误
1. The power supply voltage is too low1.电源电压过低
Troubleshooting steps故障诊断步骤
①Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 2.去步骤2。
②Check 12V battery voltage检查蓄电池电压
1. Power status is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”,断开蓄电池负极。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。
Standard voltage value: about 12.5V标准电压值：约12.5V
Are the test results normal?检查结果是否正常？
Yes是 Go to step 4.去步骤4。
No否 Go to step 3.去步骤3。
③Check DCDC output voltage检查DCDC输出电压
1. The vehicle is powered on.车辆上电。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。
Standard voltage value: about 14V标准电压值：约14V
Are the test results normal?检查结果是否正常？
Yes是 Charge the 12V battery and replace it if necessary.对蓄电池进行充电，必要时更换蓄电池。
No否 Inspect DCDC and its lines.检修DCDC及其线路。
④Check the airbag electronic control unit IG power circuit检查安全气囊电控单元IG电源线路
Graphic
1. Power status is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”,断开蓄电池负极。
2. Disconnect the airbag electronic control unit harness connector BD51.断开安全气囊电控单元线束接插件BD51。
3. Connect the negative terminal of the 12V battery and the power status is "ON".连接蓄电池负极,电源状态“ON”。
4. Use a digital multimeter to measure the voltage between pin 1 of the BD51 and ground.用数字万用表测量BD51的1号针脚与接地之间的电压。
Standard voltage value: about 14V标准电压值：约14V
Are the test results normal?检查结果是否正常？
Yes是 Go to step 5.去步骤5。
No否 Repair or replace the airbag electronic control unit IG power harness.维修或更换安全气囊电控单元IG电源线束。
⑤Replace airbag electronic control unit更换安全气囊电控单元
1. Replace the airbag electronic control unit with a new one and check whether the fault code and symptoms are eliminated.更换新的安全气囊电控单元，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Look for causes from other symptoms.从其他症状查找原因。
  Caution:注意：
♦  After replacing the airbag electronic control unit, you need to use a diagnostic tool to recalibrate the airbag electronic control unit.更换安全气囊电控单元后，需用诊断仪对安全气囊电控单元重新标定。