P200717 - TroubleshootingP200717-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
P200717	Electronic fan overvoltage fault电子风扇过压故障	1. The low-voltage power supply voltage is too high1.低压电供电电压过高

Troubleshooting steps故障诊断步骤

①Power on check上电检查

1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 2.去步骤2。

②Check 12V battery voltage检查蓄电池电压

1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正、负极之间的电压。 Standard voltage value: about 12.5V标准电压值：约12.5V Are the test results normal?检查结果是否正常？ Yes是 Go to step 3.去步骤3。 No否 Discharge the 12V battery and replace it if necessary.对蓄电池进行放电，必要时更换蓄电池。

③Check DCDC output voltage检查DCDC输出电压

1. Power status "ON".电源状态“ON”。 2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正、负极之间的电压。 Standard voltage value: about 14V标准电压值：约14V Are the test results normal?检查结果是否正常？ Yes是 Go to step 4.去步骤4。 No否 Inspect and repair DCDC and related lines.检修DCDC及相关线路。

④Check the electronic fan power supply circuit检查电子风扇供电线路

1. Check whether the electronic fan power supply circuit is faulty.检查电子风扇供电线路是否存在故障。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 5.去步骤5。 No否 Repair or replace the electronic fan power supply harness.维修或更换电子风扇供电线束。

⑤Replace electronic fan更换电子风扇

1. Replace the electronic fan with a new one and check whether the fault code and symptoms are eliminated.更换新的电子风扇，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 6.去步骤6。

⑥Replacing the thermal management integrated module更换热管理集成模块

1. Replace the thermal management integrated module with a new one and check whether the fault code and symptoms are eliminated.更换新的热管理集成模块，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。   Caution:注意： ♦  After replacing the thermal management integrated module, you need to use a diagnostic instrument to recalibrate the thermal management integrated module.更换热管理集成模块后，需用诊断仪对热管理集成模块重新标定。