Troubleshooting › Cooling system › Diagnosis
B1C6E12-故障诊断 · T00606685

 B1C6E12 - TroubleshootingB1C6E12-故障诊断

Fault code description故障码说明
DTC故障码(DTC)
Fault code description故障码描述
Possible cause of failure可能故障原因
B1C6E12
Front blower control output short circuit to power supply (PWM blower)前鼓风机控制输出端对电源短路（PWM鼓风机）
1. The wiring harness is short-circuited to the power supply1.线束对电源短路
Troubleshooting steps故障诊断步骤
①General inspection一般检查
1. Check the blower control output wiring harness for damage, breakage, etc.检查鼓风机控制输出线束是否存在损坏、断裂等现象。
2. Check whether there is any loose connection or damage to the wiring harness connector.检查线束接插件是否存在虚接、损坏等现象。
Are the test results normal?检查结果是否正常？
Yes是 Go to step 2.去步骤2。
No否 Repair or replace faulty wiring harness or connector.维修或更换故障线束或接插件。
②Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 3.去步骤3。
③Check blower control output wiring检查鼓风机控制输出线路
1. Check the blower control output harness for a short to power.检查鼓风机控制输出线束是否对电源短路。
Are the test results normal?检查结果是否正常？
Yes是 Go to step 4.去步骤4。
No否 Repair or replace the blower control output wiring harness.维修或更换鼓风机控制输出线束。
④Replace speed control module更换调速模块
1. Replace the speed control module with a new one and check whether the fault code and symptoms are eliminated.更换新的调速模块，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 5.去步骤5。
⑤Replace blower更换鼓风机
1. Replace the blower with a new one and check whether the fault code and symptoms are eliminated.更换新的鼓风机，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 6.去步骤6。
⑥Replacing the thermal management integrated module更换热管理集成模块
1. Replace the thermal management integrated module with a new one and check whether the fault code and symptoms are eliminated.更换新的热管理集成模块，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Look for causes from other symptoms.从其他症状查找原因。
  Caution:注意：
♦  After replacing the thermal management integrated module, you need to use a diagnostic instrument to recalibrate the thermal management integrated module.更换热管理集成模块后，需用诊断仪对热管理集成模块重新标定。