B3C0117 - TroubleshootingB3C0117-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
B3C0117	PM2.5 sensor supply voltage is higher than the thresholdPM2.5传感器供电电压高于阈值	1. The power supply voltage of the PM2.5 sensor is too high1.PM2.5传感器的供电电压过高

Troubleshooting steps故障诊断步骤

①Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 2.去步骤2。
②Check 12V battery voltage检查蓄电池电压
1. Power status is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”,断开蓄电池负极。 2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。 Standard voltage value: about 12.5V标准电压值：约12.5V Are the test results normal?检查结果是否正常？ Yes是 Go to step 3.去步骤3。 No否 Discharge the 12V battery and replace it if necessary.对蓄电池进行放电，必要时更换蓄电池。
③Check DCDC output voltage检查DCDC输出电压
1. The vehicle is powered on.车辆上电。 2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。 Standard voltage value: about 14V标准电压值：约14V Are the test results normal?检查结果是否正常？ Yes是 Go to step 4.去步骤4。 No否 Inspect DCDC and its lines.检修DCDC及其线路。
④Check PM2.5 sensor supply voltage检查PM2.5传感器供电电压
	1. Power on the vehicle and turn on the air conditioner.车辆上电，开启空调。 2. Use a digital multimeter to measure the voltage between pin 1 of the thermal management integrated module harness connector FB44 and ground.用数字万用表测量热管理集成模块线束接插件FB44的1号针脚与接地之间的电压。 Standard voltage value: about 12V标准电压值：约12V Are the test results normal?检查结果是否正常？ Yes是 Go to step 5.去步骤5。 No否 Replace the thermal management integrated module.更换热管理集成模块。   Caution:注意： ♦  After replacing the thermal management integrated module, you need to use a diagnostic instrument to recalibrate the thermal management integrated module.更换热管理集成模块后，需用诊断仪对热管理集成模块重新标定。
⑤Replace PM2.5 sensor更换PM2.5传感器
1. Replace the PM2.5 sensor with a new one and check whether the fault code and symptoms are eliminated.更换新的PM2.5传感器，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。