Light control

Page 100

Light control

Activating auto headlamp

Switch on the vehicle power supply, tap the AUTO headlamp soft key on the my light system interface on the center console display to automatically turn on the lamp.

If the auto headlamp function is activated, the position lamp and the low beam will be turned on or off automatically according to the ambient light.

Turning on headlamp

The headlamp is an important illumination tool for nighttime driving. Please turn on the headlamp during nighttime driving.

The headlamp consists of a low beam and a high beam, which should be switched reasonably according to the actual road condition and the driving environment.

Switch on the vehicle power supply, tap the low beam soft key on the my light system interface on the center console display to turn on the low beam.

If the auto headlamp function is activated, the low beam will be turned on or off automatically according to the ambient light.

Headlamp leveling

According to the actual vehicle condition, the low beam height can be adjusted via the my light system interface.

High/low beam switching

After the headlamp is on, push the light/ wiper control lever in the direction of arrow A to switch the headlamp to the high beam, and pull back the light/wiper control lever in the direction of arrow B to turn off the high beam. Repeatedly pull the light/wiper control lever in the direction of arrow B and reset it to switch between the high beam and the low beam in order to remind other traffic participants (such as when meeting, overtaking or crossing an intersection).

Turn signal lamp

Turn signal: Move the light/wiper control lever to ① position. After you release it, the light/wiper control lever will automatically return and the corresponding side turn signal lamp will flash continuously. After the steering wheel returns, the turn signal lamp will turn off automatically.

Page 101

When the steering wheel angle is too small, the turn signal will not automatically turn off. Slightly flip the light/wiper control lever in the same direction to ② position, and the turn signal will turn off. Lane change signal: Move the light/wiper control lever to ② position slightly. After you release it, the light/wiper control lever will return automatically, and the corresponding side turn signal lamp will flash 3 times. Turning on fog lamp Tap the rear fog lamp soft key on the My Car light system interface on the center console display, and the rear fog lammp and the headlamps will be turned on simultaneously.

Turn on the position lamp Power on the whole vehicle, and tap the on the My position lamp soft key Car light system interface on the center console display to turn on the position lamp. The position lamp will automatically turn on or off according to the ambient light, after the automatic light function is enabled. Daytime running lamp The daytime running lamp is turned on automatically when the vehicle is started and the headlamp is not on, to enable other traffic participants to detect your vehicle easily. The daytime driving lamp can be turned on or off via the center console display, when the vehicle is started and the gear is in "P".

WARNING

◆ Please use the light reasonably according to the road condition and the driving environment.

◆ T he high beam may cause dazzling to drivers of oncoming vehicles at close range, which may easily cause accidents. Therefore, please use the high beam reasonably.

WARNING (Cont'd)

◆ When the vehicle is passing a sharp turn, hill, arch bridge, crosswalk or intersection without traffic lights, the high and low beams should be turned on alternately for warning.

NOTE

◆ In some humid conditions (such as high air humidity, vehicle washing, etc.), the inside of the lamp may be covered with a layer of fog or even a small amount of water drops. This is caused by water mist that is generated due to that humid air enters the inside of the lamp through the vent hole, and the temperature of the lamp lens is relatively low, which is similar to the fogging of vehicle windows on rainy days. This is a normal physical phenomenon and will not affect the function and service life of the lamp.

◆ When the vehicle is in a dry environment or the lamps are turned on, the water vapor will gradually evaporate, and there may be residues only at the corners of the lamps, but the fogging phenomenon may appear repeatedly. ◆ If there are a lot of water drops or accumulated water in the lamps, please contact the GAC Service Center for inspection and repair. ◆ If you forget to turn off the position lamp, it will automatically go out after the vehicle power supply is turned off for a while or the vehicle enters the anti-theft state, in order to save the battery power.

◆ If one turn signal lamp on the vehicle fails, other turn signal lamps on the corresponding side and the corresponding turn signal indicator lamp in the instrument panel will flash at a higher frequency.

◆ After a collision, all turn signal lamps and turn signal indicator lamps will flash at the same time.

◆ The windshield should be replaced together with the RLS.

Page 102

Intelligence high beam system

The vehicle will automatically switch between high and low beams according to the driving environment, after the intelligence high beam system is enabled.

Activate and deactivate the intelligence high beam system The intelligence high beam system can be activated or deactivated via the central console display. When the headlight switch is set to AUTO mode and the low beams are on, pulling the light and wiper control lever towards the steering wheel for 2 seconds will activate or deactivate the intelligence high beam system. How to use the Intelligence high beam system 1. Activate the intelligence high beam system. 2. After enabling AUTO mode for the headlights via the central console display and the low beams are automatically turned on, the intelligence high beam system will be ready for operation, indicated by the instrument panel light . The vehicle will automatically switch between high and low beams based on the driving environment, with the corresponding indicator lamp on the instrument panel.

NOTE (Cont'd)

◆ The automatic lamp on/off function may not be activated in the haze environment, so please manually turn on the lamps in this case. ◆ When the headlamps/position lamps are on and the vehicle enters the Rest Mode/ Theater Mode, the headlamps/position lamps will go off automatically. When the vehicle exits the Rest Mode/Theater Mode, the headlamps/position lamps will turn on. Under the Rest Mode/Theater Mode, you can restore the exterior lights via the light/wiper control lever.

◆ When temporarily driving into an area with different traffic directions (e.g., driving in a right-traffic area and then entering a left-traffic area), the intelligent headlight system will continue to function normally without the need for manual headlamp adjustment by the driver.

System limitations The intelligence high beam system may not work normally under the following circumstances (not exclusive):

◇ The vehicle speed is low.

◇ The fog lamps are turned on.

◇ The wipers are enabled to the HI position and work continuously for a while. ◇ The driving environment is bright.

◇ Under intense driving conditions (e.g. emergency braking and sharp turns). ◇ The turn signal lamp is turned on.